Test & Tag / RCD Testing across south-east Queensland.

Test and tag services and RCD testing that keep portable equipment safe and your commercial site compliant.

Fully licensed & compliant
Commercial & industrial focus
Rapid breakdown response
50+ years combined experience

What test & tag / rcd testing covers

Test and tag is the routine check that keeps portable electrical equipment safe to use on a commercial or industrial site.

We inspect, test and tag your equipment, and test the RCDs (safety switches) protecting your circuits, so faulty equipment gets found and fixed before it causes an incident, not after.

All work is carried out and recorded by our licensed team.

How we deliver it

We work through your equipment systematically, visually inspecting each item before testing it, and tag anything that passes with the date it's due again.

RCDs are tested on the same visit where practical, so your safety switches and your portable equipment are covered in one appointment rather than two.

Test & Tag / RCD Testing

What is included

The exact scope depends on your site and equipment count. Get in touch for a tailored quote.

Visual Equipment Inspections

Inspection of electrical equipment, plugs, leads and enclosures for visible damage, wear or unsafe conditions.

Electrical Testing and Tagging

Testing and tagging of portable electrical equipment in accordance with the requirements applicable to the workplace.

Leads and Power Boards

Inspection and testing of extension leads, power boards, portable outlets and similar plug-in equipment.

Three-Phase Equipment Testing

Inspection and testing of applicable portable three-phase equipment used in commercial and industrial workplaces.

RCD Push-Button Testing

Functional push-button testing to confirm that each RCD mechanically trips and can be correctly reset.

RCD Injection Testing

Instrument testing of RCD operating times and trip performance under controlled test conditions.

Asset Registers and Reporting

Clear records of tested equipment, RCD results, failed items and identified defects for the site's compliance records.

Scheduled Testing Programs

Ongoing testing schedules arranged around the site type, working environment and applicable testing requirements.

The standards this work is measured against

Compliance isn't optional on a commercial or industrial site. Our work is measured against the same standards inspectors and insurers check against.

AS/NZS 3760

In-service safety inspection and testing of electrical equipment

AS/NZS 3012

Electrical installations, construction and demolition sites

AS 2293

Emergency escape lighting and exit signs

AS/NZS 3000

Electrical installations, the wiring rules

Why it matters on a commercial site

A faulty appliance or a safety switch that doesn't trip is invisible until it fails, and on a commercial site that can mean an injured worker or a shut down floor.

Regular test and tag and RCD testing is one of the simplest ways to catch that risk early, and keep your records ready if an inspector or insurer asks for them.

The equipment in use on a commercial site is usually a mix of owned, hired and contractor-supplied, and all of it ends up on the same floor. Knowing which items have been tested, and when they fall due again, is far easier when one team is working through the lot.

Testing is also the point where equipment that should come out of service actually comes out of service. A failed item that is tagged and removed is a problem closed, rather than one that quietly goes back on the bench.

Where we do test & tag / rcd testing

The same licensed team covers every area we work in across south-east Queensland, so the standard does not change with the postcode. Choose an area to see how we work there.

Consistent standards across every job.

Commercial &
Industrial Experts

From shopping centres to industrial sites, we understand the pressures of a live commercial environment.

Licensed &
compliant

Fully licensed in Queensland and New South Wales, and Cm3 certified for controlled commercial sites.

Service to
major projects

From routine maintenance to large scale fitouts and new builds, we scale to the size of the job.

One point
of contact

One team stays across your site, so you are not explaining the job again to someone new.

Trusted on site, trusted in the office

1 / 5

Trusted across south-east Queensland

Trusted by property managers, retailers, builders and body corporates across the region.

Retail First
CBRE
Australia Fair
Savills
Logan Hyperdome
First Asset Management
homeWORLD Helensvale
Ray White Commercial
Fairfield Gardens
Mt Gravatt Plaza
Faith Lutheran College Redlands
Future Civil Group
IGA
NNB Group

Common questions

It depends on your site and environment under AS/NZS 3760, get in touch and we'll confirm the right schedule for you.

Test and tag covers portable equipment, RCD testing covers the safety switches on your circuits, often done together.

We work through your equipment systematically rather than sampling, so nothing gets missed.

It's tagged as out of service and flagged in our report, so it isn't used again until it's repaired or replaced.

Yes. We test RCDs on the same visit where practical, so both are covered in one appointment.

Compliance guides & insights

What is test and tagging?
Testing
19 Nov 2026

What is test and tagging?

Test and tagging is the routine inspection and electrical testing of plug-in equipment, followed by a tag on the lead that records the result.

Switchboard Compliance & Upgrade Guide
Compliance
12 Jul 2026

Switchboard Compliance & Upgrade Guide

Boards are rarely replaced because they fail. They are replaced because the building changed around them and the board never caught up.

Ready when you are.

Tell us what's going on and we'll get back to you with the right next step, whether that's a quote, a site visit or a discussion about your requirements.

1300 JCS NOW1300 527 669